|
THANK
YOU
First, and again, we would like to THANK YOU for reviewing this page, and taking the time to
consider purchasing a POWERFIN Propeller setup.
To
calculate the cost of a full propeller assembly...
- Take
the price for a single blade
- Multiple
that blade model cost
times the number of blades you need.
- Then
simply add the cost of the Hub you desire.
- And
finally throw in a few dollars or so for shipping & handling.
For
example: A three blade E-model propeller setup
will include your blades...
- $169
(cost per E-model blade)
- $169
x 3 = $507
(blade cost times the # of blades needed)
- And then add a
standard three blade Apex Hub ($299 - this fits a [447/503/582] 2-cycle Rotax Gearbox mounting plate) ).
This
would bring your total to: $822 before shipping.
$507
- blades
$299 - hub
====
$806 - cost for a 3-Blade E-model complete Propeller setup
All
Hub assemblies* include mounting hardware and for pitching the blades, either:
-
A separate 1/4" dowel pin (a 1/4" hole is pre-drilled in each blade's root - this is how ALL blades were manufactured prior to 2010)
OR
-
Our new embedded
3/16" pins that are used for setting the pitch There is One embedded pin with each blade. These pin protrude through the "Window" in our Apex hubs - thus serving as a safety check for correct installation (blade's direction - Pusher or Tractor).
-
Note that if you prefer the advanced technique, we now have a new DIGITAL Protractor setup to pitch each blade's tip, and hence no drilling
is done in the blade's
root section.
(* For Rotax 912 users: Please note that the set of 6,
Threaded Insert Sleeves for the Propeller Mounting Plate are NOT included with any assembly. These MUST be REQUESTED separately with your Order: @ $69/set of 6)
The
cost of each type of propeller setup is independent of its diameter (i.e.,
does NOT depend on the length of the blade that you order)
BLADES
|
Model
|
Single Blade Cost
|
Blade Diameters Available
|
|
B
|
$189 |
48-65 inches |
|
C
|
$179 |
48-69 inches |
|
E
|
$169 |
39-53 inches |
|
F
|
$229 |
48-75 inches |
HUB
ASSEMBLIES*
| |
|
|
STANDARD Hubs
Standard Hubs
fit a mounting plate with a 6-bolt, 75-mm diameter mounting bolt pattern
(like the Rotax 2-cycle engines) |
Hub Type
|
For Blade Models
|
Cost
|
|
Standard Two Blade Apex
|
B, C & F
|
$279 |
|
Standard Three Blade
Apex
|
B, C & F
|
$299 |
|
Standard Four Blade Apex
|
B, C & F
|
$325 |
|
Standard Five Blade Apex
|
B, C & F
|
$350
|
| |
|
|
912 HUBS
912 Hubs fit a mounting plate with a 6-bolt, 4-inch (101.6-mm) diameter mounting bolt pattern
(like the Rotax 4-cycle engines: 912 & 914) |
Hub Type
|
For Blade Models
|
Cost
|
|
* Rotax 912 Three Blade
Apex
|
B, C & F
|
$335 |
|
* Rotax 912 Four Blade
Apex
|
B, C & F
|
$350 |
|
* Rotax 912 Five Blade
Apex
|
B, C & F
|
$378 |
* For Rotax 912 users: Please note that the set of 6,
Threaded Insert Sleeves for the Propeller Mounting Plate are NOT included with any assembly. These MUST be REQUESTED separately with your order: @ $69/set of 6 |
|
|
|
Special 'E' Hubs fit a mounting plate with a 6-bolt, 75-mm diameter mounting bolt pattern
(like the Rotax 2-cycle engines) but they have smaller blade sections than the Standard Hubs, to accommodate the 'E' blades) |
Hub Type
|
For Blade Models
|
Cost
|
Special 75-mm Three Blade Apex
|
E's Only
|
$289 |
| |
Shipping
a two or three blade propeller assembly within the lower 48-U.S. States is approximately $35.00.
Most
international orders will ship UPS International - Expedited Service; or US Mail upon request.
If you wish a quote on shipping an international order, please supply an address
with a postal code so we can quote shipping prices.
*All
Propeller and Hub assemblies include mounting hardware for the Rotax B, C,
or E Gearbox and for the Hirth gearbox.
When
ready to order please have all of the pertinent information available (see
our Order form) so we can quickly process your order.
POWERFIN
accepts Visa and MasterCard. Checks and money orders may be mailed to us for pre-paid orders.
|
