POWERFIN Pricing

To continue to serve your propeller needs, POWERFIN has expanded with its relocation to
El Campo, Texas - just
65-miles SW of Houston.

We are in the process of doubling (again) our manufacturing capacity!

907 S. Mechanic
El Campo, TX 77437
Ph: 979-543-7933

PRICING

First, and again, we would like to THANK YOU for reviewing this page, and taking the time to consider purchasing a POWERFIN Propeller setup.

To calculate the cost of a full propeller assembly...

Take the price for a single blade
Multiple that blade model cost times the number of blades you need.
Then simply add the cost of the Hub you desire.
And finally throw in a few dollars or so for shipping & handling .

For example: A three blade E-model propeller setup will include your blades...

$169 (cost per E-model blade)
$169 x 3 = $507 (blade cost times the # of blades needed)
And then add a standard three blade Apex Hub ($299 - this fits a [447/503/582] 2-cycle Rotax Gearbox mounting plate) ).

This would bring your total to: $822 before shipping.

$507 - blades
$299 - hub
====
$806 - cost for a 3-Blade E-model complete Propeller setup

All Hub assemblies* include mounting hardware and for pitching the blades, either:

A separate 1/4" dowel pin (a 1/4" hole is pre-drilled in each blade's root - this is how ALL blades were manufactured prior to 2010)
OR
Our new embedded 3/16" pins that are used for setting the pitch There is One embedded pin with each blade. These pin protrude through the "Window" in our Apex hubs - thus serving as a safety check for correct installation (blade's direction - Pusher or Tractor).
Note that if you prefer the advanced technique, we now have a new DIGITAL Protractor setup to pitch each blade's tip, and hence no drilling is done in the blade's root section.

(* For Rotax 912 users: Please note that the set of 6, Threaded Insert Sleeves for the Propeller Mounting Plate are NOT included with any assembly. These MUST be REQUESTED separately with your Order: @ $69/set of 6)

The cost of each type of propeller setup is independent of its diameter (i.e., does NOT depend on the length of the blade that you order)

BLADES

*Model*	*Single Blade Cost*	Blade Diameters Available
B	$189	48-65 inches
C	$179	48-69 inches
E	$169	39-53 inches
F	$229	48-75 inches

HUB ASSEMBLIES*

STANDARD Hubs Standard Hubs fit a mounting plate with a 6-bolt, 75-mm diameter mounting bolt pattern (like the Rotax 2-cycle engines)
Hub Type	For Blade Models	Cost
*Standard Two Blade Apex*	*B, C & F*	*$279*
*Standard Three Blade Apex*	*B, C & F*	*$299*
*Standard Four Blade Apex*	*B, C & F*	*$325*
*Standard Five Blade Apex*	*B, C & F*	*$350*

912 HUBS 912 Hubs fit a mounting plate with a 6-bolt, 4-inch (101.6-mm) diameter mounting bolt pattern (like the Rotax 4-cycle engines: 912 & 914)
Hub Type	For Blade Models	Cost
* Rotax 912 Three Blade Apex	*B, C & F*	*$335*
* Rotax 912 Four Blade Apex	*B, C & F*	*$350*
* Rotax 912 Five Blade Apex	*B, C & F*	*$378*
* For Rotax 912 users: Please note that the set of 6, Threaded Insert Sleeves for the Propeller Mounting Plate are NOT included with any assembly. These MUST be REQUESTED separatelywith your order: @ $69/set of 6

Special 'E' Hubs fit a mounting plate with a 6-bolt, 75-mm diameter mounting bolt pattern (like the Rotax 2-cycle engines) but they have smaller blade sections than the Standard Hubs, to accommodate the 'E' blades)
Hub Type	For Blade Models	Cost
*Special 75-mm Three Blade Apex*	*E's Only*	*$289*

Shipping a two or three blade propeller assembly within the lower 48-U.S. States is approximately $35.00.

Most international orders will ship UPS International - Expedited Service; or US Mail upon request. If you wish a quote on shipping an international order, please supply an address with a postal code so we can quote shipping prices.

*All Propeller and Hub assemblies include mounting hardware for the Rotax B, C, or E Gearbox and for the Hirth gearbox.

When ready to order please have all of the pertinent information available (see our Order form) so we can quickly process your order.

POWERFIN accepts Visa and MasterCard. Checks and money orders may be mailed to us for pre-paid orders.

POWERFIN Propellers manufactures Light Sport propeller applications which include UAV, LSA, Ultralight, and Experimental propellers as well as wind energy generating blades.